Formerly Farkin.net - News | Forums
  • 2DIE's Avatar
    Yesterday, 11:10 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    Ah the Fire eye one says: Crown Race: Steel I guess it has a crown race, I might grab that on Friday as well as some chain tugs. Sent from my...
    77 replies | 3932 view(s)
  • 2DIE's Avatar
    Yesterday, 10:53 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    Yeah, I can't tell if the headsets I'm looking at come with a crown race or not though. None of them mention it. ...
    77 replies | 3932 view(s)
  • 2DIE's Avatar
    Yesterday, 10:43 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    41.8mm where the bearing sits Sent from my SM-N9005 using Tapatalk
    77 replies | 3932 view(s)
  • 2DIE's Avatar
    Yesterday, 10:34 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    I'm having trouble finding a bearing because I don't know the angle of the crown race on the forks and I also think the inner diamiter of the bearing...
    77 replies | 3932 view(s)
  • 2DIE's Avatar
    Yesterday, 08:18 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    It has a compressing ring and seal and top cap, I'll have to pull the fork out again though to check the bottom crown race on the fork. I think it...
    77 replies | 3932 view(s)
  • 2DIE's Avatar
    Yesterday, 07:57 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    The last pic the bearing is pulled up, it sits flush and is the right diamiter when it's in there. Sent from my SM-N9005 using Tapatalk
    77 replies | 3932 view(s)
  • 2DIE's Avatar
    Yesterday, 07:38 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    The headset on the DMR would either have play or just tightening it up a 8th of a turn would make it it not turn freely, I pulled the bearings apart...
    77 replies | 3932 view(s)
  • silentbutdeadly's Avatar
    16-10-2017, 08:39 PM
    Be a bit careful with some of those headset press tools on frames with low profile headtubes or steep down tubes. The size of the push plates in...
    34 replies | 872 view(s)
  • 2DIE's Avatar
    15-10-2017, 08:56 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    It was a link to a indoor pump track in Adelaide called Pumpt https://youtu.be/vPgxlBFxnXY Can't find much about the actual pump track though,...
    77 replies | 3932 view(s)
  • 2DIE's Avatar
    15-10-2017, 08:39 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    For some reason I can't view that link above now, I went to open it again to have a read and it says I have to pay a subscription fee. I found...
    77 replies | 3932 view(s)
  • 2DIE's Avatar
    15-10-2017, 08:32 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    Maybe one day, this is just a little over a hour from me. I don't know if anything is closer. ...
    77 replies | 3932 view(s)
  • 2DIE's Avatar
    15-10-2017, 08:15 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    I haven't ridden it properly yet but all bmxs were like that back in the day and I didn't have issues, on surfaces that contact the frame it has...
    77 replies | 3932 view(s)
  • 2DIE's Avatar
    15-10-2017, 07:49 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    I put the seat down to about half of what it was, my knees are a couple inches higher than the handlebars at the top of pedal rotation like that now...
    77 replies | 3932 view(s)
  • 2DIE's Avatar
    15-10-2017, 02:07 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    I ordered the seatpost at the bike shop unseen and without knowing how much as I needed it for when my brother came over so it's ridable. It's made...
    77 replies | 3932 view(s)
  • 2DIE's Avatar
    14-10-2017, 08:18 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    Got the Rhyno Lites and Kenda K-Rads on the DMR today. Sent from my SM-N9005 using Tapatalk
    77 replies | 3932 view(s)
  • silentbutdeadly's Avatar
    13-10-2017, 11:03 AM
    Hmm I may have been blind/crazy/drunk when I replied...
    7 replies | 252 view(s)
  • silentbutdeadly's Avatar
    12-10-2017, 08:20 PM
    AOTA. Shock is on a yoke that goes around the DT to the seat stays. It actually pivots around the BB.
    7 replies | 252 view(s)
  • silentbutdeadly's Avatar
    12-10-2017, 08:09 PM
    I've learned something but I'm no more educated than I was before. Why is such a tool even required? Have frames expanded to surround BBs? Or is this...
    10 replies | 245 view(s)
  • 2DIE's Avatar
    11-10-2017, 03:44 PM
    2DIE replied to a thread 2DIEs bikes in Post Your Ride
    Gave the guy the wheels off the DMR and the white Rhyno Lite to lace the Halo hub to it for me. I ordered a Halo 14T sprocket and the Halo...
    77 replies | 3932 view(s)
No More Results
About silentbutdeadly

Basic Information

About silentbutdeadly
Location:
Somewhere flat.....
Interests:
sawdust, stereos, music, trails, rivers, deserts, life.....
Occupation:
Job? Refer to my hobbies
Trading History:
Successful Trades with: canoscott

Statistics


Total Posts
Total Posts
2,302
Posts Per Day
0.98
General Information
Last Activity
Yesterday 11:11 PM
Join Date
12-05-2011
Referrals
0

1 Friend

  1. 2DIE 2DIE is offline

    Senior Member

    2DIE
Showing Friends 1 to 1 of 1