rockmoose
his flabber is totally gastered
I thought the court order prohibited you wearing the spandex jumpsuit in public.
Sent from my SM-G935F using Tapatalk
What does your day look like?
- Thread starter johnny
- Start date
Sent from my SM-G935F using Tapatalk
pink poodle
ここには見るべきものは何もありません
I had the arse cheeks sown back on. It's all good now
hifiandmtb
Sphincter beanie
Nice deck, meet shitty wall:
WFH project 4pm-5pm, but riding this arvo instead.
Getting closer to stair construction. Never constructed stairs before. Feeling n00b.
WFH project 4pm-5pm, but riding this arvo instead.
Getting closer to stair construction. Never constructed stairs before. Feeling n00b.
stirk
Burner
Nice deck, meet shitty wall:
WFH project 4pm-5pm, but riding this arvo instead.
Getting closer to stair construction. Never constructed stairs before. Feeling n00b.
Some fine angle work there :thumb:
Ultra Lord
Hurts. Requires Money. And is nerdy.
Fuck your house is rad.Nice deck, meet shitty wall:
WFH project 4pm-5pm, but riding this arvo instead.
Getting closer to stair construction. Never constructed stairs before. Feeling n00b.
stirk
Burner
It'll only be RAD when the slide is complete. I'll give bonus rad points though if a fishing platform was installed.
hifiandmtb
Sphincter beanie
Lipstick on a pig
stirk
Burner
Does that help get the boner up? Asking for a friend..Lipstick on a pig
pink poodle
ここには見るべきものは何もありません
Well for a house without a slide it's ok
Flow-Rider
Burner
Someone snuck over the border with Hifi's offcuts.
Last edited:
He'd need new wheels for that
Fancy materials. Where dat?
Flow-Rider
Burner
Cornubia, I'd say it will be removed before long.
nzhumpy
Googlemeister who likes bikes and scandal
If they're the offcuts I seriously hope @hifiandmtb isn't a quantity surveyor...
Ah, yep. I reckon so around there.
Condition of borrowing cousin's concrete mixer was to weld up the hole in the bowl and replace the rusted loop of pipe that serves as a strut.
Cut the loop off with the cordless bandsaw.
Grabbed an offcut of 2.5t gal flat. Cut it to length, chucked it in the press to make it skid like. Then found an offcut from the rollcage. About the right length. Measured the pipe frame and the skid goes just where the pipe gets squashed. First section is oval 45mm wide, next is longer oval 25mm wide. Notched the rollcage tube 44mm then test fitted. Hmm just need to notch the other side 10mm further up at 25mm. Did that. Nice!
Tack welded it. https://www.rotorburn.com/forums/in...rom-the-fuckwits.257029/page-282#post-3320888 bought new batteries then welded it.
Done! Left the tape repair on the bowl. For now anyway.
Cut the loop off with the cordless bandsaw.
Grabbed an offcut of 2.5t gal flat. Cut it to length, chucked it in the press to make it skid like. Then found an offcut from the rollcage. About the right length. Measured the pipe frame and the skid goes just where the pipe gets squashed. First section is oval 45mm wide, next is longer oval 25mm wide. Notched the rollcage tube 44mm then test fitted. Hmm just need to notch the other side 10mm further up at 25mm. Did that. Nice!
Tack welded it. https://www.rotorburn.com/forums/in...rom-the-fuckwits.257029/page-282#post-3320888 bought new batteries then welded it.
Done! Left the tape repair on the bowl. For now anyway.
hifiandmtb
Sphincter beanie
Is the first image a human leg? Looks painful.